Showing results: 301 - 315 of 673 items found.
-
SINEAX Series -
GMC-I Messtechnik GmbH
Heavy-current power meters are programmable and may be used for the measurement of almost all quantities of an electrical power system. The application (system configuration) as well as the behaviour of the analog and digital outputs are software configurable. The measurand acquisition via programming or bus interface during normal operation is also supported.
-
ProDAQ 8036 -
Bustec Ltd.
The ProDAQ 8036 LXI trigger bus cable connects the ProDAQ 6100 LXI function card carrier or the 3030 PCI Express VXIbus slot-0 interface to any device equipped with LXI triggers. The robust, shielded cable and the die-cast connectors ensure a stable connection and prevent accidental disconnects.
-
SMT-FMC211 – LPC -
Sundance Multiprocessor Technology Ltd.
The main component of the SMT-FMC211 is the Texas Instruments 4 channel DAC – TI’s Quad 1.25GHz DAC3484. This device offers excellent SFDR performance better than 70dBc, with an output sample rate of over 312MSPS. It interfaces to an Artix-7 XC7A15T-2C FPGA using a 16 bit differential DDR bus.
-
DP-OBC-3003 -
Data Patterns Pvt. Ltd.
DP-OBC-3003 is a rugged 3U cPCI based board with 64 Digital Input channels in open/ground configuration and 4 serial ports of RS422 interface. It operates on 32-bit, 33MHz PCI bus. Four RS422 channels are incorporated with opto-isolated inputs which supports baud rates upto 115.2Kbps.
-
VM-DBA -
W-IE-NE-R, Plein & Baus GmbH
VM-DBA is a new test and diagnostic module for VME-bus systems which visualizes activities on all VME bus lines on the set of front-panel LEDs, but also allows one to digitize individual waveforms of all these lines into 2kBit -long storage memories, for a subsequent readout via VME or USB interfaces.
-
µPD720202 -
Renesas Electronics Corp.
µPD720202 is a USB host controller LSI compatible with the USB 3.0 and xHCI (eXtensible Host Controller Interface) 1.0 specifications. The system bus is compatible with the PCIe Gen2 specification. The controller provides two USB ports with LS (Low-Speed) / FS (Full-Speed) / HS (High-Speed) / SS (SuperSpeed) support.
-
µPD720201 -
Renesas Electronics Corp.
The µPD720201 is a USB host controller LSI compatible with the USB 3.0 and xHCI (eXtensible Host Controller Interface) 1.0 specifications. The system bus is compatible with the PCIe Gen2 specification. The controller provides four USB ports with LS (Low-Speed) / FS (Full-Speed) / HS (High-Speed) / SS (SuperSpeed) support.
-
W-IE-NE-R, Plein & Baus GmbH
The Mpod micro-1 crate is the smallest and low cost option for the WIENER multi-channel high and low voltage power supply system. The Mpod micro mainframe can house 1 plug-in low or high voltage modules. The integrated Mpod controller card provides10/100 Ethernet, CAN bus and USB-2 interfaces.
-
60-982-001 -
Pickering Interfaces Ltd.
The 60-982 provides a effective method of adapting trigger signals from bench instruments to the LXI Wired Trigger Bus signalling standard. The 60-982 converts M-LVDS signals on the WTB to Low Voltage TTL signals and converts Low Voltage TTL signals to M-LVDS. All 8 channels of the LXI WTB are supported in a single adaptor. Each channel of the WTB can be configured either manually or through a digital I/O to be Disabled, Driven or in Wired OR mode. The interface is fully compatible with the LXI WTB standard and counts as one node on the bus.
-
60-982-002 -
Pickering Interfaces Ltd.
The 60-982 provides a effective method of adapting trigger signals from bench instruments to the LXI Wired Trigger Bus signalling standard. The 60-982 converts M-LVDS signals on the WTB to Low Voltage TTL signals and converts Low Voltage TTL signals to M-LVDS. All 8 channels of the LXI WTB are supported in a single adaptor. Each channel of the WTB can be configured either manually or through a digital I/O to be Disabled, Driven or in Wired OR mode. The interface is fully compatible with the LXI WTB standard and counts as one node on the bus.
-
Pepperl+Fuchs GmbH
The clear assignment of a signal to a terminal while maintaining the existing instrumentation and wiring is a major advantage of remote I/O . A second is the significantly reduced wiring through the use of a bus interface to the control system - remote I/O offers the best of two technologies and is therefore ideally suited for modernizing and expanding process plants.
-
Axiomtek Co., Ltd.
The COM Express Type 6 modules are designed with all components necessary and offer the most updated bus interfaces. The COM Express modules satisfy a wide range of vertical embedded applications with features of great computing performance and rich I/O capabilities, and reduce customers' time-to-market and ownership cost.
-
Axiomtek Co., Ltd.
The COM Express Type 10 modules are designed with all components necessary and offer the most updated bus interfaces. The COM Express modules satisfy a wide range of vertical embedded applications with features of great computing performance and rich I/O capabilities, and reduce customers' time-to-market and ownership cost.
-
W-IE-NE-R, Plein & Baus GmbH
The Mpod mini crate is the small and low cost option for the WIENER multi-channel high and low voltage power supply system. The Mpod mini mainframe can house up to 4 plug-in low or high voltage modules. The integrated Mpod controller card provides10/100 Ethernet, CAN bus and USB-2 interfaces.
-
EXC-1553ExCard/Px-1760 -
Excalibur Systems, Inc.
This credit card sized interface supports up to two dual redundant 1760 channels and is compatible with all common variations of MIL-STD-1760 providing a wide range of features normally found only on full size testers.Multi FunctionEach channel of the EXC-1553ExCard/Px-1760 operates simultaneously as a Bus controller and/or multiple (up to 32) Remote Terminals, or as a Triggerable Bus Monitor. The card supports error injection and detection. The card’s small size and compatibility with notebook computers make it the perfect solution for performing system simulation of the MIL-STD-1760 bus, in the lab and in the field. Single Function Each channel of the EXC-1553ExCard/PxS-1760 operates either as a Bus Controller, Remote Terminal, or Bus Monitor.The EXC-1553ExCard/Px-1760 and EXC-1553ExCard/PxS-1760 cards are supplied with C drivers, including source code, Merlin+ Windows software and may be used with Exalt, Excalibur’s Analysis and Laboratory Tools, a Windows monitoring application.Note: Some laptops do not supply the average and peak power voltages required by the ExpressCard specification. The EXC-1553ExCard/Px-1760 may not function properly in these laptops.